Tuesday, 14 April 2009

14th April 2008 - Left side windows

I started today by cutting out a piece of 2mm acrylic sheet to make the left door window. I'd been puzzling how to mount this but eventually decided to use the simple approach of screwing it to the window surround. I've got a large stock of countersunk #6 Torx head stainless screws left over from the Vans so match drilled the window to the frame and then countersunk the acrylic and dimpled the surround to take the #6 screws. This has the advantage that the window is easily replaceable and is very secure. Next I fabricated the aluminium panel used to mount the rear window. This was match drilled to the tabs installed previously - http://tailwindbuild.blogspot.com/2009/03/26th-march-2009-left-rear-window-mount.html . The rear edge and the bottom edge were folded inwards 90 degrees to stiffen the panel and the top edge and front edge bent in slightly using an edge roller to fit tightly against the door frame and top longeron. At this point a problem became apparent: I wanted to have the bottom of the rear window in line with the bottom of the door window and bottom of the front window. However, the line of the stub stringer that forms lower mount for the rear window frame starts at the door post exactly level with the bottom of the window in the door and then slopes downwards as the fuselage narrows towards the rear. In order to keep the window bottom in-line it was necessary to start the opening 4 inches behind the door post, shorten two of the mount tabs and use an uneven placement of the lower window mounting screws. The rearwards start does have the advantage that it will hide the aileron and flap linkages and the screws will be hidden by the fabric which will cover the rear window frame. I don't think the fact that there is an angle between the bottom of the window and the stringer will look odd once the covering is in place. I'm continuing to keep my to-do list up-to-date http://tailwindbuild.blogspot.com/2009/03/25th-march-2009-list.html and was able to completely remove one item today. I'd been assuming that I would mount a VOR antenna on the horizontal stabiliser. However, I emailed the guru of antenna for homebuilt aircraft - Bob Archer and he very kindly sent me a design for a dipole antenna and matching balun that can be built inside the wooden wing. Not only will this be much neater but the cost will be much less than a commercial VOR antenna.

Posted by Picasa

Monday, 13 April 2009

13th April 2009 - Left Door Skin

A couple of days ago I ordered the tubing to make the engine mount. The tubing kit I had ordered from ACS had included a length of 1/2" * 0.049 which would have been OK for an O-200 mount but the plans call for 1/2" * 0.058" for an O-235. Today I fabricated the skin for the left hand door. First a sheet of 0.025" 6160-T6 aluminium sheet was cut to approximate size to cover the complete door frame. Then this was slotted to fit over the two hinges. Next, the outline of all of the tubing was drawn onto the sheet. The sheet was then removed and holes laid out for the #4 screws that secure the skin to the door frame. The skin was then replaced on the frame and holes match drilled with a 2.3mm drill through the skin and the frame - a total of 37 in all. The 2.3mm holes in the frame were then tapped out to take #4 screws and the holes in the sheet opened up to allow the screws to pass through. I've found some really neat 1/4" long pan head #4 screws that take a 1/16" allen key to tighten them. The front edges of the door skin were then folded at right angles to butt against the forward door post and the remaining edges trimmed to give about 1/2" overlap at the rear and bottom and 1/4" at the top where the door has to open under the wing. The door skin was then temporarily screwed into place on the door frame and the door hung on the fuselage. The gap along the front of the door from the bottom up to the the window was just right to allow a strip of door seal rubber to completely close it. The gap above the bottom of the window started OK but then widened unacceptably towards the top. This was corrected by notching the front bottom edge of the above door panel by about 3/16" and then pivoting the top of the side window angles rearward from their bottom fastening and re-drilling through the side window - this closed the gap perfectly but will mean I need to replace the left side window as it now has slotted and/or duplicated holes in the rear edge. The final job today was to cut out for the window. The line of the bottom of the front side window was carried across to the door and a couple of holes drilled to locate its position on the inside. The opening was drawn by using the spacing from these holes to the door frame cross member all the way round the frame. 1/4" holes were drilled at the four corners and a 1mm thick stainless steel cutting blade in the angle grinder used to cut out round the hole. The angle grinder works superbly cutting aluminium sheet creating a straight clean edge that just needs a quick file to clean up.

Posted by Picasa

Friday, 3 April 2009

3rd April 2009 - Forward fuselage complete

No post yesterday because I was half way through a whole set of tasks. But they all came together today with the completion of the structure of the forward fuselage and it's glazing. Jobs completed included: fabricating the right fuselage cheek panel and match drilling it to the support tabs and the firewall; fabricating the right windscreen support angles shown in the first picture, installing tabs 264 to 266 to support the two overdoor panels; fabricating the right overdoor panel and the right overdoor angle which closes the gap to the main screen; and trimming to final size the panel at the rear of the main screen. I won't be able to get into the workshop next week but it's always satisfying when you can look at a section that is not only complete but feels right.


Posted by Picasa

Wednesday, 1 April 2009

1st April 2009 - Left over-door panel

First job today was to complete the fairing between the bottom of the windscreen and the firewall. The holes through the screen were drilled out for #8 screws, the fairing dimpled and the screen countersunk. Next the fairing was match drilled to the firewall using a #40 drill. This will rivet in place during final assembly together with the upper mount for the cowl. The main objective for the day was to close the gap between the top of the door and the windscreen on the left side of the aircraft. First the dummy root rib was positioned to identify where joints in the panelling could be positioned to be hidden. Note the way that the top of the screen follows as much of the line of the top of the root rib as possible. This was done deliberately http://tailwindbuild.blogspot.com/2008/10/10th-october-2008-windscreen-support.html to make the intersection between the fuselage and wing as clean as possible. Next a piece of 0.025" thick 6160-T6 aluminium was cut out to fit over the spar attach brackets. The top was trimmed flush with the top of the windscreen. The bottom was folded into a "U" section to stiffen the edge where the door will seal. The "U" will also provide a support for the wing strobe and nav light cables and the pitot tube. An internal trim panel will then be screwed to the inside leg of the "U" and tabs on the top longeron to tidy up the interior. Next a piece of the 0.025" sheet was cut out and folded into a right angle section to form the joint between the top of the above door panel and the screen. This was then shaped using the shrinker to conform to the shape of the top of the screen. It was then match drilled to the windscreen support tabs and the holes dimpled/countersunk as before. That completes the above left above door panel with the exception of welding in place attach tabs for it and the internal trim panel.

Posted by Picasa

31st March 2009 - Windscreen framing

I started today by cutting out the right side front window. Then I cut out two strips of 0.050" thick aluminium which were bent using the bending brake into 90 degree right angle sections. These were then bent to match the shape of the edge of the windscreen using the shrinker tool shown in the last photo. This is a new toy bought to do this job and worked well. Using the second set of jaws it can also stretch metal to produce an outside curve. Once a good fit was achieved the right angle sections were match drilled to the fuselage tabs and windscreen. The legs of the angles were then cut to the minimum size needed to just cover the windscreen mounting tabs and the windscreen mounting channel. The aim was to minimise the impact on visibility whilst making the installation look as neat as possible. The holes through the angles, windscreen and tabs were then opened up to take a #8 screw. The holes in the angles were dimpled to allow countersunk screws to fit flush with their surface and the windscreen holes countersunk to match. Next a strip of aluminium was bent to join the windscreen to the top flange of the firewall. This needed about a 15 degree bend
along it's length to provide a neat join. This was then match drilled to the windscreen and front windscreen support tabs. Next job is to open up these holes for the countersunk #8 screws and match drill the strip to the firewall itself where it will be eventually riveted into place. So that's three items checked off the list (http://tailwindbuild.blogspot.com/2009/03/25th-march-2009-list.html) and another nearly complete and today I didn't add any unlike yesterday when it was four done and four added!
Posted by Picasa

Tuesday, 31 March 2009

30th March 2009 - Stringers complete

Today I welded into place the front steel sections of the right fuselage side stringers and then brazed the supports for the aluminium rear sections to the fuselage cross members. The process I used for positioning all the supports was to clamp a length of steel 5/8" tubing acting as a dummy stringer to the fuselage and then position the mounts which are semicircular sections of the same tubing between the cross members and the dummy stringer. Because, as it's the same diameter, the dummy stringer won't sit down into the mounts it is then possible to apply flux and then braze the mount to the cross member without having to get the dummy stringer too hot or accidentally brazing it into place as well. The 2nd picture shows the way the braze metal wicks into the space creating a neat and strong joint. The mount is offset from the cross member to allow space to pop-rivet the aluminium stringer to it from the inside.
Posted by Picasa

29th March 2009 - An Engine!

The big decision is made irrevocably - I've bought an engine. The engine was built in 1970 and is a Lycoming O-235-C2C originally out of a Grumman AA1 Yankee. Subsequently, it was installed in a pusher configuration Rutan Long-ez, hence the forwards facing exhaust pipes. Unfortunately both of these aircraft were written off - in neither case was the engine the problem, but hopefully it's third time lucky. The engine is first run and total time is only 820hours since new. I need to establish whether in the Long-ez accident the engine suffered a prop strike and needs a shock load inspection. In any event, the runout on the flange is not measurable and the prop was wood so hopefully there won't be any internal damage although the price paid allows for repair if necessary. The engine is rated at 115hp for upto five minutes and 108hp continuously. The C2C version of the O-235 is an interesting engine. It has the same cylinders and crankcase as the original O-235-C used in aircraft such as the Piper Colt, but has the same crankshaft as the current O-235-L2C and N2C. The crankcase has a conical engine mount which makes the engine mount easy to fabricate and uses much cheaper mount rubbers than the dynafocal mount engines. Now that I've got an engine I can order the tubing to fabricate the engine mount.
Posted by Picasa